Read all Instructions & Important Information below before starting treatment.
1. Apply Brow Code Lustre Step 1 - Brow Perming Solution to one brow at a time. Take care to keep solution to hair area only. Cover brows with cling wrap to ensure the hairs are fixed in an upright position. See TIMING & HAIR TYPE GUIDE below for how long to leave Step 1 on the brows.
2. After leaving Step 1 on for your desired time, remove the cling wrap and then by using a dry cotton tip, remove all the solution in an upwards motion leaving no residue. Once clean, add Step 2 - Brow Fixing Solution to both brows together. Cover again using your cling wrap again to fix the hairs into place.
3. After leaving Step 2 on for your desired time, remove cling wrap then remove all the solution in an upwards motion using a cotton tip, leaving no residue. Once clean, apply Brow Code Tint (or colour deposit) using the Brow Code 122 Brush for application of colour.
4. After waiting the desired time, remove all the solution then apply Step 3 - Brow Keratin Nourish to both brows. Use a generous amount to ensure this is applied to the hair and skin. Leave Step 3 - Brow Keratin Nourish on the brows for the client to leave with.
5. Retail the Brow Code Brow Gold Oil to your client and instruct them to nourish the hair and skin daily.
Step 1: 5-8 minutes. No longer than 9 minutes.
Step 2: 5-8 minutes.
Step 3: Client to remove after 2 hours and apply Brow Gold.
HAIR TYPE GUIDE:
Thin or Fine Brow Hairs: 4 - 5 Minutes
Medium or Normal Brow Hairs: 5 - 7 Minutes
Coarse of Stubborn Hairs: 7 - 10 Minutes
- Tint and other colour deposit techniques develop much faster after lamination due to porous hair. We therefore advise to reduce your timings and watch the development of the colour closely.
- Brow Lamination must always be performed before waxing, threading or plucking treatments. IF performing this service after to tidy brows - You must completely avoid getting ANY solution on the area to be waxed.
- Do not apply scrubs to the eyebrow area before lamination.
- Never use the same brush to apply Step 1 and Step 2. You must use two disposable brushes for both steps.
- In case of contact with eyes, wash immediately with distilled water.
HOW BROW LAMINATION WORKS:
When the Brow Perming Solution is applied, the chemical process breaks down the bonds within each hair, allowing them to morph and move into a new shape.
When the Brow Fixing Solution is applied, the hair bond remodels into the new shape.
The Brow Keratin is applied at the end of the treatment to restore moisture back into the brows and skin.
NOTE: The new brow design and shape takes up to 48 hours for the bonds to lock into place and cure, which is why it is important to emphasise that the client follows the correct aftercare for 48 hours post-treatment.
BROW LAMINATION CLIENT AFTERCARE:
What should and should not be done 24 hours post treatment for longevity of results:
- Keep brows dry for 24 hours.
- Use Brow Code Gold Brow Growth Oil daily.
- Do not apply make-up or undertake further eye treatments for at least 24 hours after your treatment.
- Avoid swimming/sauna/working out for 24-48 hours. Any excess moisture after this time can cause a slight curl/frizz to the brow hair.
- Do not allow prolonged exposure to direct sunlight or heat.
- Do not apply Retin-A, AHA or exfoliate around the brow area for 72 hours either side of the treatment.
- No self-tanning products should be used on the face for one week prior and 48 hours after treatment.
NOTE: If any stinging or swelling occurs, apply a cold compress to soothe and seek medical advice. Be sure to let the technician know of any adverse reactions.
Free standard delivery on all Australian orders over $149
$9.95 standard delivery for all other Australian orders
$20 express delivery for Australian orders*
$50 for International - extra charges may apply